Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 1 of 3      1   2   3   Next
glennzie

Junior Member
Registered:
Posts: 1
Reply with quote  #1 
Hi
Unable to use Temp mode, will override to wattage mode. Unable to saved when profile uploads to device.
After some tutorials still no luck.
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #2 
Need more info....wire type & coils...a screen shot of your wire profile, 'Mod Tab' & Device Monitor while firing would be very helpful!

Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #3 
I'm having this same exact issue myself.

  • Therion DNA75
  • OBS Engine
  • SS316L
  • Twisted Coils(24g x 24g)
  • 24g / 3mm ID
  • 6-7 wraps


I have tried a few different settings for this profile. Within the last few days it will either not stay in TC mode or it will detect the wrong resistance and use like 1-5 watts producing no vapor.
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #4 
A screen shot of your wire profile the 'General' tab, 'Mod' tab & Device Monitor, while firing, would be very helpful!
Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #5 
2017-03-23_20-50-26.jpg  2017-03-23_20-50-55.jpg  2017-03-23_20-51-47.jpg  2017-03-23_20-52-27.jpg 
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #6 
Ok...can you post another screenshot of Device Monitor with the cold ohms & live ohms selected...
Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #7 
Sorry, no idea why they where unchecked.


 2017-03-23_21-01-26.jpg
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #8 
Also...a screen  shot showing that wire setting in the Materials tab...
Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #9 
2017-03-23_21-06-18.jpg 
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #10 
You must be using a TCR value...  .00092...you may have an unstable connection somewhere... I would check all your connections on you atty....deck screws etc...make sure the 510 pin on the atty is good & clean...clean the 510 connection on the device with some iso alcohol & cotton swab...
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #11 
Hold on...your cold ohs & live ohms are the same...looks like the coil may have been warm when you set the cold ohms into the device...looks like the cold ohms are .180...you can go to the Atomizer Analyzer on the General tab...click override ohms...enter .18...close the analyzer & upload to device...then try it...
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #12 
According to Steam Engine, that coil setup should be in the neighborhood of .15 - .18
Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #13 
I tried setting the ohms like you said and uploaded it. The first time I fired it, it popped out of TC.
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #14 
Have you tightened & cleaned yet...
Wicked0ne

Junior Member
Registered:
Posts: 13
Reply with quote  #15 
Yea, 91% iso on a q-tip. I cleaned the pin on both device and atty. Checked all the screws in the atty. When I tried to attach a different atty(that also had the same ss316L wire) it did the same thing. Pops out of TC and uses watts.
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.