Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 2 of 2      Prev   1   2
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #16 
Quote:
Originally Posted by abraxas

 

I'm too lazy to tick the preheat option for temp sensing coils in escribe. How can I solve to get a preheat of 70 watts without using preheat?Would it be nearly the same if I set my powerlevel at 70 watts and the temp at my preferred level?Guess I should get 70 watts for ramp up and then the chips sets the watts to just hold my desired temp – or am I wrong?

 



Just use EScribe Device Monitor and set the device to no pre-heat and set the wattage to 70 watts @ the temp you desire and then you can see in real time what it produces.  Nothing like hands on experience and you can answer your own question...

__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

eetlirui

Junior Member
Registered:
Posts: 1
Reply with quote  #17 
thanks
Vaperkarloz

Senior Member
Registered:
Posts: 53
Reply with quote  #18 
Jist put kanthal cvs from steam engine and its accurate to 15c and u get thay preheat
abraxas

Junior Member
Registered:
Posts: 12
Reply with quote  #19 
Quote:
Originally Posted by Vaperkarloz
Jist put kanthal cvs from steam engine and its accurate to 15c and u get thay preheat


i have my doubts
Vaperkarloz

Senior Member
Registered:
Posts: 53
Reply with quote  #20 
Quote:
Originally Posted by abraxas


i have my doubts


Dont forget to lock ohms at 20c. Then go on escribe the .000X number is crucial. Better than the chinesse chips having a hard time to .000 not fsk ohm slice .0000001atty resistance but as long as u have the 4th digit right it should work, works for me.
Vaperkarloz

Senior Member
Registered:
Posts: 53
Reply with quote  #21 
Then again i was trying the tornado chip coil (kanthal) otherwise i use ss(specially in mech mods) the kanthal taste is disgusting
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #22 
Quote:
Originally Posted by Vaperkarloz
Dont forget to lock ohms at 20c. Then go on escribe the .000X number is crucial. Better than the chinesse chips having a hard time to .000 not fsk ohm slice .0000001atty resistance but as long as u have the 4th digit right it should work, works for me.


Don't lock ohms it stops the mod working out the coil resistance properly and can make using ss very difficult.

__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
abraxas

Junior Member
Registered:
Posts: 12
Reply with quote  #23 
i think vaperkarloz suggests locking ohms when using kanthal to get an accuracy of 15°c with the se-cvs in tc-mode (he mentioned ss later). of course you a right with not locking (guess you mentioned this advice already 50 times). but nevermind... in my opinion every single post of him in this topic is nonsense or offtopic. i hope to mention my opinion is ok with the rules, but to be on the safe side... vaperkarloz: no offense... i'sure u r better than me and of course prettier.
letsavit

Junior Member
Registered:
Posts: 20
Reply with quote  #24 
My pre heat setting for big fat kanthel coils

Press fire button, blow for 1 second while coils heat up then inhale....works on a mech, must work on a DNA200 too...!
abraxas

Junior Member
Registered:
Posts: 12
Reply with quote  #25 
appreciated, thx. did this too, but after vaping ka1 with preheat i realised that its much better and fits my needs better. it also had some negative side effects in my case eg. sometimes it caused leaking. i also think the technical potential of our products should be used and i'm glad that a dna has more possibilities than a mm although i still have two mechs as my "iron reserve".
letsavit

Junior Member
Registered:
Posts: 20
Reply with quote  #26 
Was said tounge and cheek but might try this on the DNA see if I can break the mech pre heat habbit, can't see why they won't give us pre heat on kanthel due to "safety" we now have 250 watts at hand that can been thrown at any wire or atty...I can't be the only one that's selected the wrong profile.... 80 watts kanthel at a kayfun with nife don't taste that good....!
abraxas

Junior Member
Registered:
Posts: 12
Reply with quote  #27 
Quote:
Originally Posted by abraxas

thx for posting this statement. I really appreciate that evolv cares about our safety. I can imagine that preheat with a non temp sensing material would be quiet dangerous.

Maybe somebody can help me (pls don't test it):

I was thinking a lot about how to accelerate the ramp up of my stock kanger dual 0.8 ohm coils (2x 1.6) used in my evod tank without the option of a time based preheat. In the end I thought about buying a dna 200 mod.

Would it help to pump the max wattage (based on the ohms of the coil it should something around 101 watt) in the f*?!%#g tiny coil to get a faster ramp up? Would it affect the lifetime of the coils or the lifetime of my mouth? Would it be dangerous???

I have another question regarding preheat in tc mode:

I'm too lazy to tick the preheat option for temp sensing coils in escribe. How can I solve to get a preheat of 70 watts without using preheat?Would it be nearly the same if I set my powerlevel at 70 watts and the temp at my preferred level?Guess I should get 70 watts for ramp up and then the chips sets the watts to just hold my desired temp – or am I wrong?

Owning a dna 75 mod but just using a joyetech device which I bought after they released preheat for kanthal – it's really a shame. evolv, make an effort and give us preheat for non tc.



exactly what i meant...
Vaperkarloz

Senior Member
Registered:
Posts: 53
Reply with quote  #28 
I actually found best consistent vape with dc ss316l clapton 26/32 with locking the resistance, use escribe to modify it, using the other profile unlocked then in morning fire and lock compare on escribe and what worked best was tweaking the last 2 points on escribe, always lock in tc or gunk will mess up the vape quality with inconsistent resistance. Tried the non locking and had to constantly change temperature. Don't have to do that when locking it. Btw managed ni80 tc accurate to ~2c as long as .000X is accurate, accurate to .00X ull get a 10c variation but not if you have the fourth number nailed. And yes, lock it. Vaporflask dna40 always got the ni200 resistace on point and kept it steady.
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.