Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 3 of 5      Prev   1   2   3   4   5   Next
Modbustersecig

Avatar / Picture

Member
Registered:
Posts: 73
Reply with quote  #31 
That's strange I have not seen a DNA/ 200 or 250 read cells off using escrib unless I have faulty cell or bad faulty connection if the voltage were it goes in to the board reading dose not match Escrib reading I would request return authorization
__________________
Any one seen the fire extinguisher I don't believe that's vapor
djboa

Junior Member
Registered:
Posts: 5
Reply with quote  #32 
the original poster has a mod with the same exact problem rma'd on the way to evolv ... since I am from europe I would love to avoid shipping it back and forth. 
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #33 
hum.... you might fill out a ticket and explain the issue and let Evolv guide you.... yours ran a week after update then quit..... may be hardware issue??

@mustave posted earlier about 1_2_SP5 and said this "  Beginning to suspect I have a hardware issue and the firmware upgrade was sort of coincidental. But I'm now in email communication with Evolv and we shall see".

__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

Modbustersecig

Avatar / Picture

Member
Registered:
Posts: 73
Reply with quote  #34 
Ops I understand screen shot of device montor can shed light on a problem some times
__________________
Any one seen the fire extinguisher I don't believe that's vapor
olegasan

Junior Member
Registered:
Posts: 8
Reply with quote  #35 
IMG_0384-20-01-17-08-56.jpeg  IMG_0386-20-01-17-08-56.jpeg 

I have same problem with Therion DNA166 from box. I have inserted batteries and see blinking logo Lost Vape when push the fire bottom. If I press bottom longer the second I see «check battery» and logo of empty battery. Installing SP5, restoring defaults, using another part of batteries does not help. If I try to do hard or soft reset in Escribe it says «Hard/soft reboot command issued» and nothing happen. Device Monitor in Escribe shows in Cell 1: 0,01V, in Cell 2: 5,20V.

I don’t know what to do. Please help.


EDMKEV

Junior Member
Registered:
Posts: 10
Reply with quote  #36 
@olegasan did you update to SP 5.2? and then had those issues? Seems like alot of people having troubles after updating to the new service package..
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #37 
Verify that your battery settings in Escribe are set for 2 cell & not 3 cell. My Therion 166 is updated to the newest firmware...battery settings are...Lithium Polymer & 2 cell...no problems
Modbustersecig

Avatar / Picture

Member
Registered:
Posts: 73
Reply with quote  #38 
Quote:
Originally Posted by olegasan
IMG_0384-20-01-17-08-56.jpeg  IMG_0386-20-01-17-08-56.jpeg 

I have same problem with Therion DNA166 from box. I have inserted batteries and see blinking logo Lost Vape when push the fire bottom. If I press bottom longer the second I see «check battery» and logo of empty battery. Installing SP5, restoring defaults, using another part of batteries does not help. If I try to do hard or soft reset in Escribe it says «Hard/soft reboot command issued» and nothing happen. Device Monitor in Escribe shows in Cell 1: 0,01V, in Cell 2: 5,20V.

I don’t know what to do. Please help.

just checking 5.2 volts on cell 2 or pack should be max 4.2 per cell no less than 3.2 with pack between 6.5 and 8 volts using two 18650 edit or two cell

__________________
Any one seen the fire extinguisher I don't believe that's vapor
olegasan

Junior Member
Registered:
Posts: 8
Reply with quote  #39 

EDMKEV, my mod had those issues from the box. I have received parcel with mod tomorrow.

giz_60, I recognized those issues and then updated to the newest firmware and check battery settings in Escribe. But it does not help.

Modbustersecig , in my battery charger every my battery shows 4,2V 

EDMKEV

Junior Member
Registered:
Posts: 10
Reply with quote  #40 
Wow i cant believe that..hopefully these guys can figure something out, I'm baffled that it came that way out of box though since i bought my mod just about a week ago and my VT167 is fairly new as it was programmed in late December by evolv before being sent to H Cigar i guess..

Guess it was just bad luck yours came like that
Modbustersecig

Avatar / Picture

Member
Registered:
Posts: 73
Reply with quote  #41 
OK sp 5 just under 30000 puffs same board i be-leave one more cell a pic is worth a 1000 words  set up nice.PNG 

__________________
Any one seen the fire extinguisher I don't believe that's vapor
Modbustersecig

Avatar / Picture

Member
Registered:
Posts: 73
Reply with quote  #42 
I did not notice it till after i posted that is  a terrible temp line for a DNA 250 i switched to my Boreas RTA Big difference 
borase on the250.PNG 


__________________
Any one seen the fire extinguisher I don't believe that's vapor
creative420

Junior Member
Registered:
Posts: 1
Reply with quote  #43 
Quote:
Originally Posted by olegasan
IMG_0384-20-01-17-08-56.jpeg  IMG_0386-20-01-17-08-56.jpeg 

I have same problem with Therion DNA166 from box. I have inserted batteries and see blinking logo Lost Vape when push the fire bottom. If I press bottom longer the second I see «check battery» and logo of empty battery. Installing SP5, restoring defaults, using another part of batteries does not help. If I try to do hard or soft reset in Escribe it says «Hard/soft reboot command issued» and nothing happen. Device Monitor in Escribe shows in Cell 1: 0,01V, in Cell 2: 5,20V.

I don’t know what to do. Please help.



I had same problem with my new Therion DNA166 and then I figured out that it was configured for 3 cells instead of 2, now it's working as charm [smile]
EDMKEV

Junior Member
Registered:
Posts: 10
Reply with quote  #44 
ya try the above, i once had the VT133 and i guess it had changed from 3 battery from 2 battery, and the mod would flash on for second and stop working
put it back onto Escribe and changed it back to 2 battery configuration and it started working perfect again..

but i believe i read in one of the Escribe updates or SP's that they had fixed that problem..not positive but worth a try!
olegasan

Junior Member
Registered:
Posts: 8
Reply with quote  #45 
EDMKEV, I have done it and a lot times, but nothing helps. See my video:
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.