Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 1 of 2      1   2   Next
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #1 
just build a 0.37ohm dual 316L with 26ga..@3.0..10 wrap...So my problem is when in temp mode it keeps coming up with temp protect warning...and thats anything between 30 watts and 60 watts..at 450F..im using TCR..0.00093 which is for Stainlees steel....im i doing somthing wrong?
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #2 
temperature protected is just a message letting you know that you have reached your set temp. are you not getting the vape you want? too weak?
__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #3 
Yes way to weak...yeah i know why the warning comes up but i dont understand why?.....works well in wattage mode at 65watts..although the ohms keeps changing in wattage mode..in temp mode the ohms is stable..@0.37...checked with atimizer test as well and its the same
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #4 
Also im starting to think that my coils could be a little to close to the out edge of the tfv8 rba and cauing the rime to get to hot...just a guess
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #5 
Quote:
Originally Posted by Darth vapes
Also im starting to think that my coils could be a little to close to the out edge of the tfv8 rba and cauing the rime to get to hot...just a guess


The Smok TFV atty's utilize a floating 510 pin the base, which can cause issues in TC mode, especially with their RBA's. I had one that would work fine with an OEM coil, but had no continuity with the RBA, unless I pushed up really hard from the bottom on the 510 pin.

Quote:
Originally Posted by Darth vapes
Yes way to weak...yeah i know why the warning comes up but i dont understand why?.....works well in wattage mode at 65watts..although the ohms keeps changing in wattage mode..in temp mode the ohms is stable..@0.37...checked with atimizer test as well and its the same


The watts raising in wattage mode is normal due to the resistance rising as the wire is heating up.
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #6 
Hmm!...Might have to start thinking about getting an RTDA...Any recomendations?...Would like at least 5ml capacity but as short as posible
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #7 
On the Therion 166, any atty up to a 25mm will look good...much wider than that is going to probably have some over hang ...I personally prefer the Steam Crave RDTA's...but there are alot of good ones out there...
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #8 
Ok Thank you!
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #9 
[thumb]
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #10 
Had a look around and decided to go for the Avocado 24
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #11 
The Avacado 24 has a 2 piece 510 pin..one is a long bolt that connects to the positive post & then a smaller one that is the actual 510 pin. As long as they are both good & tight, should work...
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #12 
Yes thats true...been watching a few reviews on it as well...seems once you get the wicking right it works really well..so should be a good tank..its about $48.00 here in New Zealand which makes it pricey..so hopefully it runs well..keep my wicks nice and short as possible
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #13 
Also been looking for a good vtc5 battery ecig file for 2 vtc5s...the one i downloaded off of here is not quite right...battery low comes on at 15%...and that was using 70 watts all day...and yet the LG HG2 profile i also got from here..works to well!..as in it keeped fireing when battery bar was competely empty!...for how long?....dont know?...i had 4 or 5 more puffs then switched to vtc 5s....i have my soft cell set to 2.7..i dont want to go any lower than that......Batteries are always charged on my skyrc mc3000....which showed the flat vtc5s around 3.32 volts...also i always charge my 18650s at 0.75Ma....So looking for a good vtc5 file that has been setup using Therion 166
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #14 
It's kinda odd because it comes with a tri-tool in the kit...2 different sized hex drivers & a phillips driver...but it requires a flat head driver to remove the pins to clean & to change juice flavors...[confused] or at least mine did...
Darth vapes

Member
Registered:
Posts: 36
Reply with quote  #15 
LOL..Yeah i know!...should have been a flat top!...not a philips
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.