Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 1 of 4      1   2   3   4   Next
ziaibrahimadv@yahoo.com

Junior Member
Registered:
Posts: 28
Reply with quote  #1 
Fuse on my DNA200 has been blown.... is there any alternate except to sold a new one or sending the board to Evolve for replacement or repair.

Suppose, if i remove the blown fuse and short both connections of the fuse with a wire, will it work? if yes please suggest a wire and its AWG.

Thank You 
black lace

Avatar / Picture

Senior Member
Registered:
Posts: 861
Reply with quote  #2 
Am on mobile, but There is a thread somewhere, if you s earch for blown fuse. As a get out of jail you could solder a piece of wire to where the fuse sits and then use an automotive fuse between that and the battery, the data sheet should have the fuse rating, dont believe your wire would need to be to heavy a guage, compatable to the fuse.
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #3 
http://evolvapor.forumchitchat.com/post/replacement-fuses-7764035
http://evolvapor.forumchitchat.com/post/how-to-change-the-fuse-7585633
there are probably more threads to

__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
ziaibrahimadv@yahoo.com

Junior Member
Registered:
Posts: 28
Reply with quote  #4 
Quote:
Originally Posted by black lace
Am on mobile, but There is a thread somewhere, if you s earch for blown fuse. As a get out of jail you could solder a piece of wire to where the fuse sits and then use an automotive fuse between that and the battery, the data sheet should have the fuse rating, dont believe your wire would need to be to heavy a guage, compatable to the fuse.


Have anyone done this before? Can u refer some picture or diagram etc.?
black lace

Avatar / Picture

Senior Member
Registered:
Posts: 861
Reply with quote  #5 
Sos mate am still on mobile, if you cant find anything through search and dont feel confident about it i would very much recomend putting a ticket in and wait for advise..
do you know what issue caused the fuse to burn up.
ziaibrahimadv@yahoo.com

Junior Member
Registered:
Posts: 28
Reply with quote  #6 
Quote:
Originally Posted by black lace
Sos mate am still on mobile, if you cant find anything through search and dont feel confident about it i would very much recomend putting a ticket in and wait for advise.. do you know what issue caused the fuse to burn up.


Thanks for the reply......you may reply to this when u will be free.

I have read and view the DNA200 data sheet portion relevant to "Fuse" is reproduced as under:

Fuse
Because of the energy and power stored in the battery, the DNA 200 includes an onboard 25 amp SMT fuse. The fuse is located on the underside of the PCB near the B+ battery terminal, and is labelled “Fuse” In normal operation the fuse should never blow. However, in the event of an error or short circuit on the board, the fuse will protect the battery. Should it need to be replaced, the fuse is manufactured by Schurter , part number 3413.0332.22

Replacement is accomplished by de-soldering the blown fuse from the board and soldering on a new fuse.


No i dont know, i even dont know what are the general reasons of blowing the fuse.

I have found a automotive fuse with an online vendor, which is described as:


Features:

Fuse Current Rating: 25A 

Voltage Rating DC:32V

Picture:
fuse.jpg 

 Will it work ???????????????

 


ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #7 
Quote:
Originally Posted by ziaibrahimadv@yahoo.com
Quote:
Originally Posted by black lace
Sos mate am still on mobile, if you cant find anything through search and dont feel confident about it i would very much recomend putting a ticket in and wait for advise.. do you know what issue caused the fuse to burn up.


Thanks for the reply......you may reply to this when u will be free.

I have read and view the DNA200 data sheet portion relevant to "Fuse" is reproduced as under:

Fuse
Because of the energy and power stored in the battery, the DNA 200 includes an onboard 25 amp SMT fuse. The fuse is located on the underside of the PCB near the B+ battery terminal, and is labelled “Fuse” In normal operation the fuse should never blow. However, in the event of an error or short circuit on the board, the fuse will protect the battery. Should it need to be replaced, the fuse is manufactured by Schurter , part number 3413.0332.22

Replacement is accomplished by de-soldering the blown fuse from the board and soldering on a new fuse.


No i dont know, i even dont know what are the general reasons of blowing the fuse.

I have found a automotive fuse with an online vendor, which is described as:


Features:

Fuse Current Rating: 25A 

Voltage Rating DC:32V

Picture:
fuse.jpg 

 Will it work ???????????????

 

there's a few people here in the forum that have used automotive blade fuses. they do work. just make sure it's no more than 25 amp rating. but your best bet, if your board is under warranty, have evolv replace the fuse for you. 

__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
1000moths

Junior Member
Registered:
Posts: 3
Reply with quote  #8 
http://www.digikey.co.uk/product-detail/en/3413.0332.22/486-1690-1-ND/2870103

http://www.mouser.co.uk/ProductDetail/Schurter/3413033222/?qs=tk5EcTX4n4yNf01GmJFMyw%3d%3d

http://uk.farnell.com/schurter/3413-0332-22/fuse-smd-ust-1206-25a/dp/1829475RL

All the same product just different vendors.

If you're not in the UK just google "3413.0332.22" and that should give you some results for the Schurter fuse, which is a direct replacement.

End of the day if you can de-solder the blown one (use de-solder wick with some flux to remove as much of the existing solder as possible, then clean the pads, re-tin them slightly, and the solder the new fuse one side at a time applying some downward pressure so it makes good contact.
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #9 
In the UK Radio Spares are cheapest IIRC and if you have a local branch you can order online and pick them up, link in one of the posts I linked to above.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
black lace

Avatar / Picture

Senior Member
Registered:
Posts: 861
Reply with quote  #10 
Quote:
Originally Posted by ziaibrahimadv@yahoo.com
Quote:
Originally Posted by black lace
Sos mate am still on mobile, if you cant find anything through search and dont feel confident about it i would very much recomend putting a ticket in and wait for advise.. do you know what issue caused the fuse to burn up.


Thanks for the reply......you may reply to this when u will be free.

I have read and view the DNA200 data sheet portion relevant to "Fuse" is reproduced as under:

Fuse
Because of the energy and power stored in the battery, the DNA 200 includes an onboard 25 amp SMT fuse. The fuse is located on the underside of the PCB near the B+ battery terminal, and is labelled “Fuse” In normal operation the fuse should never blow. However, in the event of an error or short circuit on the board, the fuse will protect the battery. Should it need to be replaced, the fuse is manufactured by Schurter , part number 3413.0332.22

Replacement is accomplished by de-soldering the blown fuse from the board and soldering on a new fuse.


No i dont know, i even dont know what are the general reasons of blowing the fuse.

I have found a automotive fuse with an online vendor, which is described as:


Features:

Fuse Current Rating: 25A 

Voltage Rating DC:32V

Picture:
fuse.jpg 

 Will it work ???????????????

 

ok am back in the room, think its been covered well enough now anyway but it was an automotive 12volt 25 amp, the thread I reffered to is at http://evolvapor.forumchitchat.com/post/mod-just-stopped-working-without-being-plugged-in-7524885?highlight=mod+just+stopped+working+without+being+plugged&trail=15 the fuse mentioned on the second page wasn't condemned as wouldn't work but I cannot emphasise enough if your not confident or have any warranty I would put a ticket in, you cant just put a great blob of solder on, possibly covering both contacts and then installing a fuse further down, it is quite micro, and you still haven't got to the initial cause for the fuse to blow,,
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #11 
Well done finding that thread Black Lace, I tried the other day and couldn't.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
black lace

Avatar / Picture

Senior Member
Registered:
Posts: 861
Reply with quote  #12 
found it while on phone, lol,  its an old phone so it found that old post easy, lmao,,
ziaibrahimadv@yahoo.com

Junior Member
Registered:
Posts: 28
Reply with quote  #13 
Quote:
Originally Posted by ChunkyButt200
Quote:
Originally Posted by ziaibrahimadv@yahoo.com
Quote:
Originally Posted by black lace
Sos mate am still on mobile, if you cant find anything through search and dont feel confident about it i would very much recomend putting a ticket in and wait for advise.. do you know what issue caused the fuse to burn up.


Thanks for the reply......you may reply to this when u will be free.

I have read and view the DNA200 data sheet portion relevant to "Fuse" is reproduced as under:

Fuse
Because of the energy and power stored in the battery, the DNA 200 includes an onboard 25 amp SMT fuse. The fuse is located on the underside of the PCB near the B+ battery terminal, and is labelled “Fuse” In normal operation the fuse should never blow. However, in the event of an error or short circuit on the board, the fuse will protect the battery. Should it need to be replaced, the fuse is manufactured by Schurter , part number 3413.0332.22

Replacement is accomplished by de-soldering the blown fuse from the board and soldering on a new fuse.


No i dont know, i even dont know what are the general reasons of blowing the fuse.

I have found a automotive fuse with an online vendor, which is described as:


Features:

Fuse Current Rating: 25A 

Voltage Rating DC:32V

Picture:
fuse.jpg 

 Will it work ???????????????

 

there's a few people here in the forum that have used automotive blade fuses. they do work. just make sure it's no more than 25 amp rating. but your best bet, if your board is under warranty, have evolv replace the fuse for you. 


Can you refer any picture / diagram of the wiring?? 
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #14 
Wiring the auto fuse: you would just put it it the positive wire from the battery connector, just cut that wire and solder each end to the fuse.
auto fusing.png 


__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
Modbustets

Member
Registered:
Posts: 66
Reply with quote  #15 
https://www.bluesea.com/products/5297/easyID_Fuse_25_Amp

Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.