Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 2 of 2      Prev   1   2
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #16 
No change while spinning the cells...after reviewing the chart farther back, for some reason sometimes cell 1 takes a dive at the initial fire & then they both start sawing & at other times cell 2 takes the dive before the sawing...but now both cells seem to be running pretty much together...

Edit...almost forgot...only screen I am getting is advising about temperature being achieved...no check battery or imbalanced cell
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #17 
does it do it in reg wattage/kanthal mode as well?  can you try it it at, say at 100w?
__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #18 
Nope...no fluctuation in power mode at 100w...fairly consistent fire...but then again, it seems to operating normal now...working like usual in TC mode now too....

Capture20.PNG 

ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #19 
it might be a poor connection somewhere between the board and your build. i.e. 510 wires (soldering), 510 itself, poor atty for TC. loose wire post connections. dirty 510. if you open atomizer analyzer and tap on the atty or mod, does the resistance change a considerable amount? does this behavior occur with all attys or just one in particular?

it's super hard trying diagnose problems like these over the internet, but we'll see if we can figure this out.

__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
giz_60

Avatar / Picture

Senior Member
Registered:
Posts: 796
Reply with quote  #20 
I already check the atomizer in the analyzer & it seems to very stable. The deck on this atomizer screws directly to the 510 on the mod...no contact points to transfer resistance between the coil & the mod...when re-wicking a few minutes ago, double checked all screws on deck & they are all tight, no hot spots on the coils...everything as it should be.  Always clean the 510 on mod & atty with IPA every time I remove an atty my mods...It has done this with other atty's as well....but now it seems to be working as it is supposed to be...

I can understand the diagnosing over the net thing...
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #21 
ya glad it's working correctly again, hope it stays that way. maybe as a last ditch effort, if it happens again, re-flash the firmware you're running. other than that i'm out of ideas! lol. something's not letting the board deliver the wattage you have selected. it's either on the battery side or atty side, is my GUESS.
__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.