Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 1 of 2      1   2   Next
MikeTheVapeDude

Avatar / Picture

Senior Member
Registered:
Posts: 156
Reply with quote  #1 
Just thought I'd mention this. My mods are now going up past 9V. My current build maxes it out at 9.2V at 200W and I haven't built anything a little higher to see if it goes past this, but, evidently 9V isn't the max output voltage anymore.
__________________
I can't be bothered to get creative enough for one of these, so this is what you get for my signature.
Csd113

Avatar / Picture

Junior Member
Registered:
Posts: 1
Reply with quote  #2 
i cant get the update firmware promt to occur on the new escribe 75
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #3 
Quote:
Originally Posted by Csd113
i cant get the update firmware promt to occur on the new escribe 75
From what I gather only the newer firmware that's included is only for the DNA75. 
I tried to flash one of my 200's with the 75's firmware and it couldn't see the device.
(EScribe version 1.0.56) 

__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
mikepetro

Senior Member
Registered:
Posts: 189
Reply with quote  #4 
Quote:
Originally Posted by MikeTheVapeDude
Just thought I'd mention this. My mods are now going up past 9V. My current build maxes it out at 9.2V at 200W and I haven't built anything a little higher to see if it goes past this, but, evidently 9V isn't the max output voltage anymore.


Be cautious with that firmware. There have been several reports of DNA200s dying a couple hours after being flashed to the leaked firmware. Mine was one of them!
Wayneo

Senior Member
Registered:
Posts: 296
Reply with quote  #5 
To be clear for the entire community we should all remember and probably post both the software version, and the firmware version. I'm running 1.0.56 on the software side. I'd have to fire up VMware to see my firmware version. At that version of software there was no firmware update for the DNA200.
__________________
My old tired eyes don't look at skewed, moire filled cell phone photos. Printscreen - Sniping tool or [ALT]+[PRT SCN], open MSPaint and paste [CTRL]+[V]
Ghostrider

Member
Registered:
Posts: 32
Reply with quote  #6 
I am running escribe 1.0.56 and firmware 25-04-2016 on the wismec and lavabox.
mikepetro

Senior Member
Registered:
Posts: 189
Reply with quote  #7 
There was only 1 version that included a FW update for the DNA200, that was version 1.0.49 (dated 4/25/16) and it accidentally got leaked here (then pulled). It was intended for "beta testers" only.

There is NOT any "release version" of new DNA200 FW at the time of this posting.

If you ever installed 1.0.49 (dated 4/25/16) then the FW will still be in your folder, even though you have upgraded to 1.0.56 or whatever.
The newer versions dont include DNA200 FW, but they dont delete the old ones either.

If you run this 1.0.49 FW (dated 4/25/16) and your DNA200 dies, dont say you weren't warned!!!!

If you are running it, I would recommend rolling back to a previous version!
MikeTheVapeDude

Avatar / Picture

Senior Member
Registered:
Posts: 156
Reply with quote  #8 
I can't revert back, my device locks at Upload Settings on ANY firmware besides 4-25 now. I can change it back, but, any other firmware will not work. I didn't know what I was doing was risky, it was from a download from an Evolv supported German website. I'm a bit pissed off at this point.
__________________
I can't be bothered to get creative enough for one of these, so this is what you get for my signature.
mikepetro

Senior Member
Registered:
Posts: 189
Reply with quote  #9 
I rolled back on one device successfully.

I was on the 04-25-16 FW.

I flashed the 02-23-16 firmware on it, got the "Upload Settings" message, and checked all the settings in Escribe and clicked the "Upload Settings to Device" button.
It worked and I have been using the device for 3 days since.

[image]
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #10 
I rolled 3 of mine back within a couple of hours but I used the 2016-02-29 EScribe to do it.
mikepetro did you do yours with the beta EScribe?

__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
mikepetro

Senior Member
Registered:
Posts: 189
Reply with quote  #11 
Quote:
Originally Posted by dwcraig1
I rolled 3 of mine back within a couple of hours but I used the 2016-02-29 EScribe to do it.
mikepetro did you do yours with the beta EScribe?

I rolled mine back with v1.0.55 which I think may have been beta only.
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #12 
It sounds like all versions that have the materials tab should be able to do a roll back then....perhaps.
__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #13 
So here is what I just did. I flashed my DX200 with the "pulled" software (4/25 FW) then I uninstalled that EScribe and installed the one on the DNA75 page of Elolv's site and flashed it back to 2/23. All went smoothly.
__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #14 
dwcraig1 is correct you just need the previous version of EScribe to roll back from 4-25, the current ones in the Early fw thread and you will have to set defaults and start over if you have not saved a config recently.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #15 
Quote:
Originally Posted by VapingBad
dwcraig1 is correct you just need the previous version of EScribe to roll back from 4-25, the current ones in the Early fw thread and you will have to set defaults and start over if you have not saved a config recently.
Well except I used EScribe 1.0.56 to roll it back to the 02/23 FW.
This came from Evolv's DNA75 page.

__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.