Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 2 of 4      Prev   1   2   3   4   Next
Jaquith

Avatar / Picture

Senior Member
Registered:
Posts: 237
Reply with quote  #16 
There are many good points but a few are either not exactly correct or arguably not correct.

Just a few examples I'd reexamine: USB Recovery, Weak Battery, 100% Charge, Warranty message, USB won't connect, Resistance, Temperature Control, not charge...

I'm doing this on my phone reading 2-3 lines at a time.

Don't get me wrong it's an excellent and interesting start.
blueridgedog

Avatar / Picture

Moderator
Registered:
Posts: 573
Reply with quote  #17 
Feel free to suggest updates/expansions.  They are a collection of solutions gathered from this forum and are open to any edits you want to suggest.
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #18 
you're tips/tricks look all fine to me blueridgedog. if not, nick, james or john from evolv would of chimed in and suggested any changes. thanks for the list if i run into any problems, i'll be sure to go down the list! [smile]
__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #19 
Nick did on post #9 when it was 95% as it is now and thought it was good and just added a level of detail on recovery charging.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
blueridgedog

Avatar / Picture

Moderator
Registered:
Posts: 573
Reply with quote  #20 
Yea...I want to be clear that these are gleaned from this forum and are intended to be a "one stop" collection of helpful facts or solutions.  Any additional suggestions are welcome and I have solicited review from Evolv staff.  I am not trying to put "my" spin on solutions, but to collect items in one place as it is otherwise hard to locate them.


black lace

Avatar / Picture

Senior Member
Registered:
Posts: 861
Reply with quote  #21 
It would be good if it was locked to the top of topic list and then you could add to it as and when..
JaySoCal

Member
Registered:
Posts: 33
Reply with quote  #22 
One thing I have found for battery not fully charging is after it reaches 100% screen stays on but charge never resumes as voltage drops.
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #23 
This may be worth including http://evolvapor.forumchitchat.com/post/tungsten-vapers-8050705?pid=1291725974  about 6 V output limit with 2 cell operation.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
blueridgedog

Avatar / Picture

Moderator
Registered:
Posts: 573
Reply with quote  #24 
How would you phase it?  Something like:  Limited output for Two Cell operation based on coil ohms?
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #25 
Not sure, the 133 W power limit is well known, but the 6 V output limit is not and will lower the max resistance level VxV/P, it should not effect the low res limit as that comes from the max current limit.

Maybe
Higher coil resistances limit the max power with two cells
or
Max resistance is lower for two battery cell operation


The DNA 200 is a step down converter designed to run from 3 Li cells is series and is limited to a max output voltage of 9 V.  After multiple user requests in this forum Evolv released firmware that allowed it to operate from 2 series cells at reduced power (133 W).  The max output voltage has also changed to 6 V for 2 series cell implementations.  So you need a resistance between 0.0532 ohm and 0.27 ohm for 133 W (max power) in this mode.  The max resistance can be calculated by voltages squared divided by power, the max voltage is 6 V so 36/power will give you your max res a any supported power level.


No doubt my pros could be improved, not my strong suit.

__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
mikepetro

Senior Member
Registered:
Posts: 189
Reply with quote  #26 
It would be nice if Evolv released Power charts, similar to the original ones in the specs, that represented a 2S configuration.
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #27 
Just for you Mike, Kanthal limits from R= P/I.I = V.V/P
R limits.png


__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
Scarab

Member
Registered:
Posts: 53
Reply with quote  #28 
blueridgedog thank you for the valuable information! I translated it to russian.
dparisan

Junior Member
Registered:
Posts: 1
Reply with quote  #29 
Hello,
I have DNA 133, connected to escribe and detect that 1 0f my batteries are dead then i change the power source to Power Supply option on my escribe upload it again after that i unplugged the usb cable

Then i found that that i still can firing for quite sometimes, even tough the battery indicator is empty…

Why is that…

TQ for the attention

Attached Images
jpeg IMG_4894.JPG (70.32 KB, 27 views)
jpeg IMG_4895.JPG (71.09 KB, 24 views)

VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #30 
Power supply mode bypasses all the battery protection so don't use it with a battery other than for testing, but it looks like you have a wiring or connection problem with the balance connection I would try cleaning that first.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.