Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 2 of 2      Prev   1   2
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #16 
Quote:
Originally Posted by Clairenix

Hey guys, got something to follow up this discussion.

 

I've noticed the the OEM soft cell cutoff was 2.5v, I've read alot that it was recommended to be 3.09v.. Would you guys have any good guesses as to why it was 2.5v default?

3.09v is common cutoff for lipos. I use 2.7v for the cutoff when I'm using 18650's. And 3v when I'm using a lipo. 2.5v Is too low for the device. The board won't operate under 2.5v.

__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
Clairenix

Junior Member
Registered:
Posts: 15
Reply with quote  #17 
Mine seems to be operating just fine at 2.5v but ofcourse I'm still curious as to why it's what ThinkVape set it at. I'm planning on bumping it up at around 2.7-2.9 but I'm not really seeing its effects for the past few days I've been using it.
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #18 
If it's the same hardware cutoff as the 200 it won't make much difference if set below 28.5 volts. I don't know what the hardware cutoff for the 250 is though.
__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
ChunkyButt200

Avatar / Picture

Administrator
Registered:
Posts: 1,516
Reply with quote  #19 
Quote:
Originally Posted by Clairenix
Mine seems to be operating just fine at 2.5v but ofcourse I'm still curious as to why it's what ThinkVape set it at. I'm planning on bumping it up at around 2.7-2.9 but I'm not really seeing its effects for the past few days I've been using it.
bump it up to 2.85, like dwcraig1 suggested. my point about the 2.5v value is, the board will not operate below that voltage. just because you set "2.5" in EScribe doesn't mean the device accepted that value. there's a minimum voltage the board needs to see before it'll even turn on. there's a difference between voltage at rest and voltage under load as well. also DNA's have a hard cutoff voltage (non adjustable) and soft cutoff voltage (which you're able to set in EScribe). 

__________________
1.21 JIGAWATTS............GREAT SCOTT!........WHAT THE HELL IS A JIGAWATT?
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •
Latest versions of EScribe: DNA 200 • DNA 75  Common problems
EVOLV HELP DESK - https://helpdesk.evolvapor.com/?a=add
LOST VAPE WARRANTY REPAIR - http://www.lostvaperepaircenter.com
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #20 
3.09 for LiPos, lower for 18xxx
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
jacknb1ack

Junior Member
Registered:
Posts: 2
Reply with quote  #21 
hello, i just bought finder167 and did the same mistake as OP. sadly i still can't download ecig file from this forum even after my account is approved ... can some one send the file to my email please ? thanks you in advance
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #22 
I'm beginning to wonder if your country's internet footprint, your browser, or your provider is blocking .ecig type files? I have Zipped the file so you may be able to get the attached zip file.  Let us know if you can get this zip file?

 
Attached Files
zip Finder_167.zip (8.70 KB, 77 views)


__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

gregg raps

Junior Member
Registered:
Posts: 3
Reply with quote  #23 
Hi there....thanks. I cannot open the zip file.
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #24 
Were you able to download the zip file from here?
__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

gregg raps

Junior Member
Registered:
Posts: 3
Reply with quote  #25 
Yes but it won't open saying format not supported.
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #26 
You must unzip the file (extract it) in order to use the file that was zipped...

https://answers.stanford.edu/solution/how-do-i-zip-and-unzip-files-and-folders-do-i-need-winzip-or-stuffit


__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

jacknb1ack

Junior Member
Registered:
Posts: 2
Reply with quote  #27 
Quote:
Originally Posted by retird
I'm beginning to wonder if your country's internet footprint, your browser, or your provider is blocking .ecig type files? I have Zipped the file so you may be able to get the attached zip file.  Let us know if you can get this zip file?


thank you very much, now i can download it. 


kevmat

Junior Member
Registered:
Posts: 3
Reply with quote  #28 
Anyone with a VaporShark DNA250 running the escribe software?  I was running the software with custom profiles on my Wisemac Releaux DNA200 with no problems till the Wismec quit on me with the 'Check Battery' fault.  Just got the VaporShark DNA250 and having problems with the software. Uninstalled and reinstalled escribe. No 'Mod' tab among other issues. 
VapingBad

Avatar / Picture

Administrator
Registered:
Posts: 2,449
Reply with quote  #29 
On the Wismec check the ground screw in the battery sled is tight, normally under a white foam plug.  In EScribe Options - User Interface select Advanced or Manufacture to get the Mod tab to display.
__________________
• I am not employed by nor do I represent Evolv Inc.  All opinions are my own, they are just opinion not fact and can be wrong •

Latest versions of EScribe: DNA 200/250DNA 75
Common problems
lsx2

Junior Member
Registered:
Posts: 1
Reply with quote  #30 
thanks bro, i was do same thing [biggrin] [biggrin] [biggrin]
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.