Evolv DNA Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 4 of 4      Prev   1   2   3   4
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #46 
Quote:
Originally Posted by Wayneo
Has anyone managed to retest with this latest SP5 to see if this is working again? I know mine is somwhere around here, I'll just have to hunt it down.


If I am not mistaken they are still working on that one....  Still ? here.....

__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #47 
I'm pretty sure it is unchanged as yet.
__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
Wayneo

Senior Member
Registered:
Posts: 296
Reply with quote  #48 
Danke. [thumb]
__________________
My old tired eyes don't look at skewed, moire filled cell phone photos. Printscreen - Sniping tool or [ALT]+[PRT SCN], open MSPaint and paste [CTRL]+[V]
mactavish

Senior Member
Registered:
Posts: 127
Reply with quote  #49 
Quote:
Originally Posted by retird


If I am not mistaken they are still working on that one....  Still ? here.....


What am I missing here, did the copper plug stop working at some point. I think the last SP I installed was SP3.
Spirometry

Senior Member
Registered:
Posts: 135
Reply with quote  #50 
SP3 added some extra protections. Reading the ultra low resistances with the copper plug will just display a question mark.
mactavish

Senior Member
Registered:
Posts: 127
Reply with quote  #51 
Quote:
Originally Posted by Spirometry
SP3 added some extra protections. Reading the ultra low resistances with the copper plug will just display a question mark.


Thanks! That's odd though since when I wrote my posts earlier in this thread, I believe I was using SP3. I did see the "?", but after making the plug really tight, it showed the resistance. I could be mistaken on the SP version I was using at the time. I do hope they fix the issue.
mactavish

Senior Member
Registered:
Posts: 127
Reply with quote  #52 
Quote:
Originally Posted by Wayneo
Has anyone managed to retest with this latest SP5 to see if this is working again? I know mine is somwhere around here, I'll just have to hunt it down.


I just ran SP5, on my new VS Switchbox DBA75, which came from VS with a ".004" already set. Zeroed settings, use the copper plug, and got the EXACT same number. So I would say it worked!
retird

Avatar / Picture

Administrator
Registered:
Posts: 1,187
Reply with quote  #53 
6-5-2016 is the latest firmware version for the DNA75.  Check the lower right hand corner of Device Monitor and the Switchbox should show that version.

Vapor Shark did an excellent job programming the Switchbox with the production utility.

__________________
I am not an employee of and do not represent Evolv Inc.  My opinions are just that and are not meant to be fact or even correct.

Wayneo

Senior Member
Registered:
Posts: 296
Reply with quote  #54 
Quote:
Originally Posted by mactavish
... new VS Switchbox DBA75, which came from VS with a ".004" already set.
Very sharp looking mod. Thanks for trying.

When I ran it with the Feb software, I fely very uncomfortable with how much I tightened it down, especially on my Reuleaux, knowing the quality of that 510.

__________________
My old tired eyes don't look at skewed, moire filled cell phone photos. Printscreen - Sniping tool or [ALT]+[PRT SCN], open MSPaint and paste [CTRL]+[V]
mactavish

Senior Member
Registered:
Posts: 127
Reply with quote  #55 
Quote:
Originally Posted by Wayneo
Very sharp looking mod. Thanks for trying.

When I ran it with the Feb software, I fely very uncomfortable with how much I tightened it down, especially on my Reuleaux, knowing the quality of that 510.


You are welcome. With SP5 I did NOT have over tighten, but I did not test that aspect on any of my other DNA devices.
Wayneo

Senior Member
Registered:
Posts: 296
Reply with quote  #56 
Has anyone managed to retest with this latest EScribe 1.2 SP5.2 to see if this is working again? 

Or even better, is it on any official list for it to be fixed in the future, which should then show up in the notes for each new release.

__________________
My old tired eyes don't look at skewed, moire filled cell phone photos. Printscreen - Sniping tool or [ALT]+[PRT SCN], open MSPaint and paste [CTRL]+[V]
dwcraig1

Avatar / Picture

Administrator
Registered:
Posts: 1,248
Reply with quote  #57 
Best I can tell, just checked a few of mine, is that it still doesn't function properly. EScribe 1.2 SP5.2 on my computer has firmware for 200/250 dated 12-22-2016. Still shows "?"
__________________
I am not connected with and do not represent Evolv Inc. All opinions are my own. They are just opinions and may not be correct.
Wayneo

Senior Member
Registered:
Posts: 296
Reply with quote  #58 
I'm just waiting on a few last parts before getting myself a new mod built and I'll need to run my own MFG settings. Luckily I have an old version 2016/02/23 which works. 
__________________
My old tired eyes don't look at skewed, moire filled cell phone photos. Printscreen - Sniping tool or [ALT]+[PRT SCN], open MSPaint and paste [CTRL]+[V]
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.